Run your hand along the arm of a good wood chair and you will find a curve where a corner could have been. That curve is not an accident and it is not cheap. Wood grows straight. Getting it to turn a corner and stay there is one of the oldest problems in furniture, and chair makers have found six ways to solve it.
Knowing the six will not make you a woodworker. It will make you a better buyer, because the way a curve was made tells you a good deal about how strong it is likely to be and why one curved wood chair costs more than another.
First, a word: radius
In the furniture trade a curve is called a radius. A radius corner is a corner that has been turned into a curve, and radiusing is the work of putting it there. A tight radius is a sharp turn; a generous radius is a slow, sweeping one. When a page on our site talks about a radius corner on a chair arm, this is all it means: the place where the wood turns, and turns smoothly.
Why bother curving wood at all
A curved wood arm does three jobs better than a square one. It gives the hand and forearm a soft edge to rest on. It softens the outline of the chair, so a row of them in a waiting room reads as furniture and not as a fence. And it brings warmth to a room: wood with a curve in it looks made by someone, which steel tube never quite manages.
The trouble is the grain. Wood is a bundle of long fibers, like a fistful of drinking straws. Along the fibers it is strong. Across them it snaps. So the question for every curved part is the same: do the fibers follow the curve, or does the curve cut across them?
1. Steam bending
The classic. A length of solid wood is steamed until the fibers go limp, pulled around a form, clamped and left to dry. When the clamps come off, the wood keeps the shape.
The fibers run unbroken around the bend, so a well-made part is strong for its weight, and the grain flows around the curve where you can see it. The cabinetmaker Michael Thonet built a whole industry on this in the 1800s, and the cafe chair his company introduced in 1859 is still made today.
The cost: it takes the right species, straight-grained stock, time to dry and a certain number of pieces that crack on the form.
2. Bent lamination
Slice the wood into thin strips, spread glue between them, stack them and clamp the stack over a form. Each strip is thin enough to bend cold. Once the glue cures, the strips cannot slide past each other, so the curve is locked in.
Done well it is strong and very repeatable, which is why factories like it for chair arms, legs and rockers. Look closely at the edge of the part and you can sometimes see the fine lines between the layers.
3. Molded plywood
The same idea taken wider. Sheets of veneer are glued up with the grain crossing from layer to layer, then pressed in a heated mold. This is how many curved wood seat shells and chair backs are made: one piece that bends in two directions at once, something solid wood will not do.
4. Kerf bending
Saw a row of slots most of the way through the back of a board and the board will fold around a curve, with the slots closing up on the inside. It is fast and it needs no steam, but most of the wood has been cut away at the bend. That makes it a method for cabinet panels, counters and reception desk fronts, where the curve is supported from behind. It is not a good way to make a chair arm.
5. Hot pipe bending
Thin wood, dampened and worked by hand over a hot pipe or a heated iron. This is how the curved sides of a guitar or a violin are made. It is slow, skilled, one-at-a-time work, so you will meet it in instruments and craft pieces and almost never in office furniture.
6. Compressed and chemically softened wood
The specialist end of the trade. Wood can be softened with ammonia in place of steam, or squeezed lengthwise in a press so that it will bend cold afterward, even into tight curves. Both work. Both need equipment most shops do not have, so they stay rare.
The curve that was never bent
There is a seventh way to get a curved part, and it involves no bending at all: cut the curve out of a wide board with a saw, or build it from short pieces joined at the corner. It is quick and it wastes wood. It also leaves the grain running straight off the edge partway around the curve, which is the weak direction. A well-made joint can be perfectly sound, but this is the method to ask about.
How to read a curved wood chair in a showroom
- Follow the grain. If the lines in the wood sweep around the bend with the part, the fibers were bent, not cut.
- Look at the edge. Fine parallel lines along the edge of a curved part mean layers, which means lamination.
- Look for a joint at the corner. A seam where the arm turns down into the leg means the curve was built from pieces.
- Ask about the finish. A clear or stained finish lets you see all of the above. A solid color hides it, and then even the dealer may have to ask the maker.
- Sit in it. A curve exists for the person in the chair. If your forearm does not notice the difference, the curve is decoration.
What it means for your waiting room
Most guest seating went to steel tube years ago, in large part because steel is cheap and easy to bend and wood is not. That is exactly why a wood frame with curved arms still changes a room. It tells the person waiting that somebody chose the furniture on purpose.
The chair that started this post is our wood frame guest chair with curved arms, and you can see the rest of our guest chairs beside it. To sit in one, call us at (512) 452-3375 before you visit the showroom at 8910 Research Blvd in North Austin, so we can tell you what is on the floor that day. Ask us how any chair is built. We will tell you what we know, and say so plainly when we do not.
Further reading
- Steam bending, on the method and its history
- Bentwood, on bent wood furniture in general
- The No. 14 chair, the 1859 cafe chair mentioned above
- Molded plywood, on pressed veneer shells